Build your own Xbox 360 Controller
Mar 28, · One mistake can cause your controller to have paint on the inside. For a good accent, paint the detachable pieces on the toothpicks one color (black for example) and the Front and back covers a different color (red for example). It gives the controller a nice custom look that is sure to be one of a kind%(14). Oct 03, · Fine grain. Lightly sand your entire controller. Pay closer attention to the shinny buttons - start and back buttons, the triggers, bumpers (entire top piece really) and the D-pad. Blow or brush the sand off and you are ready to paint next!
Our lab techs are working hard on some very important updates to Xbox Design Lab. Unfortunately not. Your controller starts to be created soon after you submit your order. And since it is customized specifically for you, no design changes are allowed once your order is submitted.
Sorry, because Xbox Design Lab controllers are customized specifically for paknt, they cannot be returned. I purchased my Xbox Design Lab controller before October When yoour I get my controller? You will receive an email with the tracking number once your pokemon black and white 2 how to catch landorus has been shipped. We aim to have the controller in your hands within 28 days of placing your order.
Please contact a customer service agent for assistance. You may be advised to visit www. Before attempting to exchange your controller, please take some steps to troubleshoot the problem. If this proves unsuccessful, please begin the online warranty replacement process.
All warranty exchanges must be processed online and cannot be exchanged at a Microsoft Store. I did not receive an order confirmation. How do I know if my order went through? If you do not see your controller order there, then it was not completed. Please select your design and then checkout. Pwint have been charged for my controller, but I have not received how to play gopro videos shipping tracking number.
You were hoq for your controller at the time it began to be built. It can take up to two weeks between that time and when you will receive a tracking number. You will receive an email with the tracking number once your controller ships. No, additional or spare parts are not available for purchase for the Design Lab Controller. If you would like an Xbox controller with interchangeable parts, you should check out the Xbox Elite Wireless Controller Series 2 at the Microsoft Store.
Skip to main content. Follow Xbox on Twitter, Facebook, or Instagram for updates. Frequently asked questions. Can I change my design or cancel my order after placing an order? Can I return my controller if I do not like it? How do I change the address my order is being shipped to? I received my controller and it does not look like the one I ordered. My controller is not working. What should I do? Follow Xbox.
I bought a bunch of old buttons and busted $4 controllers from ebay and when I was painting my controller, painted a few extra sets of buttons for replacement. If you're planning on having painted buttons on your controller, I strongly recommend this. Don't spray paint your joysticks. They're rubber. It won't work and you'll end up with a blue. Xbox Design Lab will be back in We’re taking a short break to make some changes. Stay tuned for updates on how to customize your Xbox Wireless Controller. Start building from selecting the shell for your controller. Choose from solid colors, chrome, original limited edition and hydro-dipped designs.
I will show you how to make you Xbox look super cool and super affordable! Remove Your Hard Drive Just press the button and pull it off.
Remove The Face Plate Just stick you thumb in the usb slot and pull with a little bit of force. Remove The Sides Now, to remove the pieces you will need a small pointed object such as a very thin torque screw or a small screwdriver.
You will now need to locate the plastic tabs within the wholes and push them in with your pointed object. Each piece has three tabs per side totaling 6 tabs for each piece. On the piece that holds the Harddrive, it can be easier to get the two tabs by going inside and pulling them out.
Also, use a spare screwdriver or other object to hold up the popped tabs. Remove The Bottom Half of the Cover Next, after the pieces have been removed, look closely and you will see small notches on the left and right sides of the system. Once again, you will need a very narrow pointed object or screw driver to successfully complete this step.
Now, starting on the side closest to the power input, push the screwdriver into the narrow space until you hear a click sound. After you have heard the click I suggest using another screwdriver or small object to keep the top and bottom of the system apart. After you have completed the clicks on the left side, this may take a few tries start on the other side and repeat the process.
Now that you have successfully finished this step, you should now easily be able to separate the bottom portion of the system. Keep this part separated and you can easily remove the 4 snap hooks on the other side of the system. After removing all the hooks you can lift away the cover of your system and begin the unscrewing process. First you need a small flat head screwdriver like the 2. Next you need a pair of vice grips or pliers and you want to grip the screwdriver with the pliers and try to unscrew the torx screw.
Once you get it loose you can just unscrew it without the pliers. Now you can simply pull off the top cover. Make sure to take out only the marked screws! Removing the DVD Housing The DVD drive just sits inside the xbox so all you have to do is pick it up and unhook the 2 cables and now you have it out. To remove the housing you have to first unscrew 4 Phillips screws on the bottom and then the cover should be able to be removed by just pulling up on it. Now we are going to cut a hole in the housing that we just removed so you can the the disk spin when playing you Xbox !
Remove all of the stickers in the housing 2. Mark where you are going to cut using a sharpie and an old CD. Make sure when you are cutting you xbox or dvd drive is no where close so dirt and metal shavings don't fly into it! Cut out the hole with a dremel and a cutting wheel but make sure not to touch the middle circle that helps keep the disk in place while spinning 5. Sand you cuts down so they are nice and smooth.
Before we get started first we have to remove the metal piece that is under the top of the cover. To do this just give it a good yank it and should snap right off. This piece is no use to us. Decide what type of window you want and sketch it out on a piece of paper. Once you are happy with what you sketched now you want to cut out the windows in the piece of paper 3. Trace the paper design on to the xbox and make sure everything is straight and parallel like you want it.
Once you have cut out the window s take you sanding block and sand down you cuts until they are smooth and on the lines. Next sand down your corners until they are also smooth and on the line. Flip the cover that we just got done cutting hole in upside down.
Now we need to cut anything out that will prevent use from allow the plexiglass to lay evenly, so with the dremel get to work and cut out anything that sticks up above the surface. NOTE: The 2 screw holes in the middle are no use to us and we can cut them out, but make sure that all 4 corner screw holes are left alone.
Sand down all the rough cuts so everything is nice and smooth 5. Test to see if you plexiglass will fit in the area that you cut out for it. Attach the plexiglass to the cover with hot glue around all the edges and anywhere else you can get it without it being visible. For this step I would suggest using 5mm LEDs because they make instillation much easier. First we will do the easy side and that would happen to be the left side.
This is because there are already holes that are the perfect size. Pick where you want to install your LEDs and slide them into the holes, make sure you push them in as far as they can go. Now take the LED's wires that you installed on the left side and solder all the negatives together 4. Time for the right side. This side is a little tricky because the hole on this side are way to small for our LED's. So you will have to drill out some holes and make sure they are the right size.
Mark the holes where you are going to drill for however many LEDs you want on that side. Drill out the holes with a bit that is closest to the size of your LEDs. Make sure to clean out your metal shavings when you are done!!!
Now take the LED's wires that you installed on the right side and solder all the negatives together 4. Now to wire them all up! Run the newly installed wires to the left side set of LEDs as cleanly and hidden as possible. Now do the same thing for the -'s Now all the LEDs are wired in a parallel and you will only have to install one resistor for all of them!
Once you find out what resistor to use wire it in on the positive lead of the LEDs. Attach about " of 30awg to the other end of the resistor. Solder about " of 30awg to the negative lead of the LEDs 4.
Remove the 4 pin dual fan power connector 6. Look at my illustration on where to install the wires. Replace 4 pin dual fan power connector once wires are installed Now power on you xbox to test you work and if you did everything correctly the LEDs should come to life! Self explanatory pretty much, just mask up what you don't want painted and then go at! Just make sure you know how to spray paint good. I would also suggest you use a special spray paint made for plastic so the paint don't chip.
Good Luck! Once you are done painting, slap everything together and there you go you have your very own very custom xbox ! Here is a video of it and of how the spinning disk effect looks! Thanks, and I hope you enjoy!!! I think using led strips would be better becayse them come in nice colors are cheap and can cut them to desired lengths and all so you could hot glue them in case were there concealed and it would inliminate the need for all that wireing and resitirors.
Reply 7 years ago on Step How about those two holes where the screws have to be bolted in. Can you just ignore those or would I have to take those into consideration?
I've been measuring a bit and it seems that this modification doesn't have those holes anymore. Could anybody help me with that? Reply 8 years ago on Introduction. Can sum1 plz help me!!
I leave in NC. I'm so tried but I will not give up! My very last step will b to do it myself but he will no it's gone. Reply 9 years ago on Introduction. Reply 9 years ago on Step 2.
This step is dangerous if your not an electrician and you wire this up wrong you could: 1. It plugs into the disc drive socket on the main board with a splitter so you can plug your drive into the splitter. Also there are a few useful features instead of just 1 colour thats comes on when you switch your console on and turns off when you turn the console off it has 7 diffrent colours to choose from with 3 diffrent settings on each colour.
You get a remote control with it too. Also you can turn the lights off so you can game in the dark without led's glaring in your face. I would do this in a second but with the red ring of death threat i don't dare. All you are doing is putting LED's in, maybe with a battery inside or something.
When you open the case the warranty becomes VOID. There are stickers on the Xbox that when removed, leave a residue letting people know that it was opened. Reply 10 years ago on Introduction. I used 12v source near the power suply for my fans. I am also instaling led lights but I don't know where to find another power source. By pilotpack Follow. More by the author:.
Did you make this project?